Shop – Hawg Wired

RS400

wpadmin — Thu, 12 Mar 2026 09:20:23 +0000

Introducing our new Reference Series, a new addition to the RC-Link Family of products. Based on our original amplifier designs, this new version is the smallest, most powerful one yet. 5 pounds of bang in a 1 pound bag just doesn’t cut it. 200W of continuous power @ 4 ohms, and 400W @ 2 ohms; if that’s not enough for in-your-face audio, we don’t know what is. This new form factor allows you to fit 2 of these in a Batwing fairing (FLHT/X), and 4 in a Sharknose (FLTR). You won’t find anything else like these amplifiers anywhere on the planet. Without a doubt, this is the heart and soul of what Hawg Wired is, and always has been all about.

XR04-100 Crossover (Single)

wpadmin — Wed, 18 Feb 2026 19:03:27 +0000

Pre-2025 model NX Series crossover. This item is for quantity one (1) crossover unit.

UAB150-24

wpadmin — Wed, 24 Sep 2025 05:38:46 +0000

Simple lightweight plate to level out the area where the OE amplifiers mount for the 23.5-current Road Glide and Street Glide style fairings. Laser-cut. no frills, aluminum plate with the right hole pattern and cut aways. Works perfect with our amps and modules. Hardware included.

Looking for a little more space and mounting options for your Road Glide? Check out our AMB150-24s bracket.

RSX/NX – RUSH4002

wpadmin — Fri, 12 Sep 2025 05:23:53 +0000

The RUSH4002 System is a complete plug and play kit for the 2014+ Rushmore platform that includes our latest reliable and performance-proven RSX400, 400-watt amplifier, NX652-150 6.5″ component speakers and a universal mounting bracket for 2014+ Batwing or Sharknose fairings. The RSX400 included in the system has a built-in pre-filter that corrects the factory curve for optimal performance so that flashing is not required. If your radio has been flashed our 2x gain mode will accommodate low input voltages as well.

NX652-150 Component Speakers:
6.5-inch carbon fiber cone
38mm Ferrofluid cooled voice coil assembly
Spider-less suspension design

RS400 Amplifier:
400-watt RMS, Class-D power amplifier. Efficient power, low heat.
Conformal coated to protect against corrosion and moisture.

WX400 Amplifier Install Kit:
Everything you need to wire up the system. Professionally terminated for Plug-N-Play installations.

RS/NX – Six Pack

wpadmin — Fri, 12 Sep 2025 04:55:44 +0000

The SIX PACK has been chiseled into perfection over the years and is the perfect solution for someone who wants all the performance they can get now and possibly add more later. Comprised of a set of our USA built NX speakers and our 400-watt reference series amplifier. Reference Series amplifiers are 2 Ohm stable and compact enough to fit two or more in most fairings.

NX652-150 Component Speakers:
6.5-inch carbon fiber cone
38mm Ferrofluid cooled voice coil assembly
Spider-less suspension design

RS400 Amplifier:
Class-D power amplifier, efficient power, low heat
Conformal coated to protect against corrosion and moisture

AR65 Speaker Adapter Rings:
Completely bolt-in with no modifications required
All hardware included

WX400 Amplifier Install Kit:
Everything you need to wire up the system. Pre-terminated and plug-in ready.

DCS4004 System w/DCM2 (DSP+Bluetooth)

wpadmin — Sat, 28 Jun 2025 09:30:13 +0000

Clean, clear, loud, expandable front system that fits both fairings and can be installed in quick time with only the fairing removed. Complete with our oil-cooled, carbon fiber component speakers and backed with an RS 400-watt digital amp, the DCS4004 is a true plug-n-play, no battery wire installation that cranks. Using the DCM2 Bandit Box re-purposes the A2B board that’s already on your bike, saving money while freeing up space. The DCM2 is curve corrected and optimized through an onboard DSP while also being bluetooth ready for user configuration via mobile app (available soon).

NX652-150 Component Speakers:
6.5-inch carbon fiber cone
38mm Ferrofluid cooled voice coil assembly
Spider-less suspension design

DCM2 (Bandit Box):
100% Plug and Play to 2024+ factory connector, no battery wires
Built-in DSP configured for 2024+ factory system
Rear speaker wire connector (high-level output to drive secondary amp)

RS400 Amplifier:
Class-D power amplifier, efficient power, low heat
Conformal coated to protect against corrosion and moisture

UAB150-24 Amplifier Bracket:
Completely bolt-in with no modifications required
All hardware included

How direct connect works

DCs4004 system
[ Harley Skyline Radio ]
│
A2B Board
(removed from stock amp)
│
[ DCM2 Bandit Box ]
├── 12V Power
├── Ground
├── Remote Out (turn-on)
└── 4ch Speaker-Level Outputs
├── ➤ Front Amp ➝ Front Speakers
└── ➤ Rear Amp ➝ Rear/Saddlebag/TourpacSpeakers

DCs4002 system
[Harley Skyline Radio]
│
Stock amp stays (silver only)
│
[ DCM1 Direct Connect ]
├── 12V Power (harness, 30a)
├── Ground (harness)
└── 4ch Speaker-Level Outputs
├── ➤ Front Amp ➝ Front Speakers
└── ➤ Rear Amp ➝ Rear/Saddlebag/TourpacSpeakers

2015+ Road Glide Glovebox Detents

wpadmin — Sat, 17 May 2025 06:38:58 +0000

GBD152 Glovebox Detent Kit

The GBD152 Detent Kit is designed to securely hold factory glovebox doors open when fully lifted,
providing easy and convenient access. This kit is compatible with all FLTR model bikes (2015 and newer)
and installs in minutes—no modifications or tools required.

Other Features:
High-quality injection-molded parts for durability
High-temperature 3M VHB double-sided tape for secure adhesion
Stainless steel ball bearings for smooth operation
Music wire compression springs for reliable performance
Made in the USA with premium materials

What’s in the box:
2x Detent Devices
Alcohol Cleaning Pads
Installation Guide

DCM1 Direct Connect Module (Non-A2B)

wpadmin — Sat, 17 May 2025 06:38:58 +0000

The DCM1 for 2024+ (non-CVO) Harley audio systems offer a true plug and play solution for your audio upgrade. No need for power and ground wires, line converters, resistors or cutting into your bike. The DCM1 plugs directly into the OE harness keeping your stock system in full operating state while passing through necessary A2B signals and power. The DCM1 senses current draw at the factory amp to enable system power. With an on-board pre-programmed DSP, tuned specifically to optimize power and sound quality for 2024+ bikes, and a 6-watt Class-D amplifier for high-level output, the DCM1 makes the installation of a high-powered system easy and clean. The DCM1 is Patent Pending.

Product highlights:
-100% Plug and Play to 2024+ factory connector (non-CVO)
-Current sensing power-on detection, no remote wire required
-Pre-tuned for curve correction and optimization on 2024+ Skyline radios
-2-Ch, 6-Watt, Class-D, high level speaker outputs for connection to amplifiers

Other Features:
-12v power and ground terminals for Direct Connection of amplifiers. Circuit limited, 35 Amp, Fused
-Factory connections eliminate need for extra wires or terminations
-Rear speaker wire connector (high-level output to drive secondary amp)
-System status and clipping LED for quick and proper setup
Dimensions: 4″x2.5″x1.5″, 6″ harness
Warranty: 1 year

What’s in the box:
1x DCM1 Module
1x 4-pin Mini-Fit input cables
Installation Guide
Mounting Hook/Loop pad
Owner’s manual

Compatible Years
Removes OE Amplifier
A2B Interface
HD Curve Correction
Discrete Channels
Fade Control
Addt'l Adjustable Parameters
Bluetooth
DSP
PWR/GND Pass-through
Remote turn-on out
Status/Clipping Indicator
Dimensions
Warranty

DCM1

2024-2025(Non-CVO)
No
Pass-through
Yes
2
Radio Controlled
N/A
No
Pre-Tuned/Fixed
Yes
No
Yes
4″x2.5″x1″
1yr

DCM2

23.5-2025(ALL)
Yes
Bandit*
Yes
4
Application Controlled**
Yes**
Yes
Pre-Tuned/Custom
Yes (w/ dedicated fuse 30A)
Yes (300mA)***
Yes
4″x2.5″x1.5″
1yr

* DCM2 repurposes the A2B interface board removed from the OE amplifier (Black or Silver, CVO or Std)
** DCM2 application required, features subject to change
*** Use to trigger amplifer(s) that require REM turn on or relays for larger current drawing devices

How direct connect works

DCs4004 system
[Harley Skyline Radio]
│
A2B Board
(removed from stock amp (black or silver)
│
[DCM2 Direct connect-Bandit Box]
├── 12V Power (harness, 30a)
├── Ground (harness)
├── Remote Out (Optional turn-on)
├── Application (DSP & Config)
└── 4ch Speaker-Level Outputs
CH1,2 ├── ➤ Front Amp ➝ Front Speakers
ch3,4 └── ➤ Rear Amp ➝ Rear/Saddlebag/Tour Pak Speakers

DCs4002 system
[Harley Skyline Radio]
│
Stock amp stays (silver only)
│
[DCM1 Direct Connect]
├── 12V Power (harness, 30a)
├── Ground (harness)
└── 2ch Speaker-Level Outputs
CH1,2 ├── ➤ Front Amp ➝ Front Speakers
ch1,2 └── ➤ Rear Amp ➝ Rear/Saddlebag/Tour Pak Speakers

Reference Series NX652-150

wpadmin — Sat, 17 May 2025 06:38:55 +0000

Our newest Reference Series NX652-150 speakers are manufactured and tested in the USA. Constructed of carbon fiber cones, PC plastic injected baskets, and a neodymium ferrofluid cooled motor assembly. These high-powered speakers are rated at 150 watts RMS. They offer extreme efficiency and full range performance while withstanding all-weather riding
conditions.

Key Features:
6.5in Carbon fiber cone
PC injected basket
38mm Ferrofluid cooled voice coil assembly
Spider-less suspension design
High energy neodymium magnet assembly
Bridge mounted, 1.25″ inverted dome aluminum tweeter
1-year warranty

What’s in the box:
2 – 6.5″ Component Speakers
2- Installation Gaskets Sets

DCM2 w/DSP+Bluetooth (Bandit Box)

wpadmin — Sat, 17 May 2025 06:38:53 +0000

Our DCM2, aka the Bandit Box, for 23.5+Harley audio systems is here. Transfer your factory amplifiers A2B board over to the DCM2, save some cash and install your choice of amplifiers and speakers while not interfering or changing a single thing about your bikes infotainment system. Get out of the box high-fidelity sound with added built-in DSP and Bluetooth connectivity allowing end user system control and tuning.

Product highlights:
-100% Plug and Play to 23.5+ factory connector
-Removes factory amplifier
-Repurposes factory A2B board for undetected and seamless integration
-Pre-tuned for curve correction and optimization on 23.5+ Skyline radios
-Works on BOTH standard and CVO applications
-4-Ch, 6-Watt, Class-D, high level speaker outputs for connection to amplifiers
-Digital signal processing via iSO and Android (App coming soon)
-13-band graphic EQ on front and rear channels +more

Other Features:
-12v power and ground terminals for Direct Connection of amplifiers. Circuit limited, 35 Amp, Fused
-12v remote terminal for turning on amplifiers or other devices (300ma Max)
-Factory connections eliminate need for extra wires or terminations
-System status and clipping LED for quick and proper setup
Dimensions: 4″x2.5″x1.5″
Warranty: 1 year

What’s in the box:
1x DCM2 Module
2x 4-pin Mini-Fit input cables
Installation Guide
Tool/Hardware kit
Mounting Hook/Loop pad
Owner’s manual

Compatible Years
Removes OE Amplifier
A2B Interface
HD Curve Correction
Discrete Channels
Fade Control
Addt'l Adjustable Parameters
Bluetooth
DSP
PWR/GND Pass-through
Remote turn-on out
Status/Clipping Indicator
Dimensions
Warranty

DCM1

2024-2025(Non-CVO)
No
Pass-through
Yes
2
Radio Controlled
N/A
No
Pre-Tuned/Fixed
Yes
No
Yes
4″x2.5″x1″
1yr

DCM2

23.5-2025(ALL)
Yes
Bandit*
Yes
4
Application Controlled**
Yes**
Yes
Pre-Tuned/Custom
Yes (w/ dedicated fuse 30A)
Yes (300mA)***
Yes
4″x2.5″x1.5″
1yr