Wiring/Kits – Hawg Wired

WHK35

wpadmin — Sat, 17 May 2025 06:38:52 +0000

HARMON/KARDON 35pin rear breakout harness. You will need this harness to gain access to the rear output channels that all Harman/Kardon radios come with from the factory. Whether you own a Street Glide with only two speakers and want to add another set or you are installing an amplifier and want your rear speaker output for signal input, this harness will give you what you need. Comes pre-terminated with twisted pair wire left/right.

Product highlights:
-Quality high strand count 18 AWG wire
-Factory correct 35 pin AMPSeal connector
-Terminated for use with any Hawg Wired amplifier
-6″ total length

What’s in the bag:
1 – 35pin rear breakout harness

This wiring kit is intended for use with any OE Harmon/Kardon radio. To utilize front/rear fade settings, the Harman/Kardon radio might need to be re-programmed by an authorized dealer.

WX400

wpadmin — Sat, 17 May 2025 06:38:49 +0000

This is all you need to install a CS/RS Series Amplifier. From the power and ground wiring to the zip ties needed to wrap everything up, it’s all in here.

Product highlights:
-Quality high strand count power and ground wire
-Professionally assembled, crimped, and soldered
-Perfect fit wire lengths
-Tailored to each application
-OE compatible connections

What’s in the bag:
1x 6′ 10 AWG Power Wire w/Black Sleeve
1x 6′ 10 AWG Ground Wire
1x 36″ Remote Turn-on Wire
1x Low level (RCA to phono) Input Cable
1x 30 Amp ATC Fuse
6x 8″ Black Zip Tie
1 x Dielectric Grease Packet

WRS04 – Rear Speaker Breakout Harness (2014+)

wpadmin — Sat, 17 May 2025 06:38:43 +0000

You will need this harness to gain access to the rear output channels that all 2014+ radios (Except Ultras and CVO) come with from the factory. Whether you own a Street Glide with only two speakers and want to add another set or you are installing an amplifier and want your rear speaker output for signal input, this harness will give you what you need. Comes pre-terminated with twisted pair wire left/right and .187″ and .250″ female spades connections to make directly connecting to any Hawg Wired amplifier system a cake walk.

Product highlights:
-Quality high strand count 18 AWG wire
-Factory correct 4 pin Molex connector
-Terminated for use with any Hawg Wired amplifiers (cut/adapt for universal)
-10″ total length

Whats in the bag:
1x Rear Speaker Breakout Harness (2014+)

WFS04 – Front Speaker Breakout Harness (2014+)

wpadmin — Sat, 17 May 2025 06:38:43 +0000

No cutting of Factory wiring. Unplug your speaker pod’s connector and use this to access the front speaker wiring and connect to and from your amplifier. Comes pre-terminated with twisted pair wire left/right and .187″ and .250″ female spades connections to make directly connecting to any Hawg Wired amplifier system a cake walk.

Key Features:
-Quality high strand count 18 AWG wire
-Factory correct 2 pin Molex connectors
-Terminated for use with any Hawg Wired amplifier
-10″ total length

What’s in the bag:
2x 10″ Speaker breakout harnesses Sets (Inside and outside buckets)

WBP16 – 2 CH Amplifier By-Pass Plug (Harman-Kardon)

wpadmin — Sat, 17 May 2025 06:38:42 +0000

If you’re removing a CVO 2 channel amplifier, use one of these to reconnect the speaker wires that are interrupted by the amp. This makes wiring up a fairing amplifier as simple as it is on non-CVO bikes and eliminates the need to cut/splice stock CVO harnesses.

Product highlights:
-Quality high strand count 18 AWG wire
-Factory correct 16 pin Molex connector
-Terminated to reconnect speaker in/out wiring
-Simple plug and play

What’s in the bag:
1 – CVO amplifier by-pass plug

This wiring plug is intended for use on CVO bikes that came from the factory with 2 channel amplifier(s). It is not useful on stock non-CVO

WXL100 – Rear Speaker Wiring Kit

wpadmin — Sat, 17 May 2025 06:38:41 +0000

Use this kit when adding speakers to saddle bags, lids, or a Tour-Pak. Long enough to run from the front fairing to the back of the bike and has pre-installed 2 pin connectors per side, it’s everything you need to get your new speakers up and running. Plug into OEM radio rear speaker output and have dealer flash the radio to activate your speakers.

Key Features:
-Quality high strand count 18 AWG automotive wire
-Quality 2 pin connectors for quick disconnect applications
-10′ total length

What’s in the bag:
1 – 10′, 4 conductor speaker wiring harness w/quick connects